Roof Pitch Calculator

Roof pitch is how many inches a roof rises for every 12 inches it runs across: a roof that climbs 6 in over 12 in is a 6/12 pitch, 26.57°. Type the rise and run in any units, or a pitch or an angle, to get the pitch, the angle in degrees, the slope as a percent and the pitch factor used to work out roof area.

Measure the run level, not along the slope. Rise and run can be in different units.

Roof pitch
6/12 Steep roof

A roof that rises 6 in over 12 in of run has a 6/12 pitch (6 in 12): an angle of 26.57° and a 50% slope.

Angle 26.57°
Slope 50%
Pitch factor 1.118

What is roof pitch?

Roof pitch says how steep a roof is as inches of rise for every 12 inches of level run, written 6/12 or "6 in 12". IKO's estimating guide calls this the slope, in inches per foot of run, and uses "pitch" for rise ÷ span (the full width): a roof 24 ft across that rises 8 ft has a pitch of 8/24 = 1/3, or a slope of 8 in per foot. Most people, and this calculator, mean the 8/12 figure.

Source IKO · Estimating How Much Roofing Is Required (roof pitch and slope, Table 1) ↗

How to calculate roof pitch

Pitch = rise ÷ run × 12

Here it is with your numbers:

  1. Divide the rise by the run: 6 ÷ 12 = 0.5.
  2. Multiply by 12 for the pitch: 0.5 × 12 = 6, so the pitch is 6/12.
  3. The angle is the arctangent of rise ÷ run: arctan(0.5) = 26.57°.
  4. Multiply rise ÷ run by 100 for the slope: 0.5 × 100 = 50%.
  5. The pitch factor is √(1 + (rise ÷ run)²): √(1 + 0.5²) = 1.118.

It means the roof climbs 6 inches for every 12 inches across. OSHA counts it as a steep roof (over 4 in 12).

Rise ÷ run is the tangent of the roof's angle, so the angle is its arctangent. The pitch factor is how much longer the slope is than the run: multiply a roof's footprint by it to get the roof's area.

Source Common Core State Standards · High School Geometry, solving right triangles (G-SRT.C.8) ↗

Low-slope and steep roofs

OSHA's construction safety rules define a low-slope roof as 4 in 12 or less and a steep roof as more than 4 in 12. The label on the result follows those definitions, decided on the pitch as shown.

Source eCFR · 29 CFR 1926.500(b), OSHA definitions of low-slope and steep roofs ↗

Common roof pitches

PitchAngleSlopeFactorOSHA
1/124.76°8.33%1.003Low slope
2/129.46°16.67%1.014Low slope
3/1214.04°25%1.031Low slope
4/1218.43°33.33%1.054Low slope
5/1222.62°41.67%1.083Steep
6/1226.57°50%1.118Steep
7/1230.26°58.33%1.158Steep
8/1233.69°66.67%1.202Steep
9/1236.87°75%1.250Steep
10/1239.81°83.33%1.302Steep
11/1242.51°91.67%1.357Steep
12/1245°100%1.414Steep
14/1249.4°116.67%1.537Steep
16/1253.13°133.33%1.667Steep
18/1256.31°150%1.803Steep
24/1263.43°200%2.236Steep

Factors are √(1 + (rise ÷ run)²) rounded to 3 decimals. IKO's printed table gives 1.157 for 7/12 and 1.356 for 11/12; worked out exactly they round to 1.158 and 1.357.

FAQs

How do you calculate roof pitch?

Measure 12 inches level along a rafter or the roof, then measure straight up to the roof: that rise is the pitch, written like 6/12. For any other run, divide the rise by the run and multiply by 12. IKO also shows how to read it from the ground with a carpenter's folding rule.

Source IKO · Estimating How Much Roofing Is Required (roof pitch and slope, Table 1) ↗

What's a 2% slope in degrees?

1.15°. A 2% slope rises 2 for every 100 across, and arctan(0.02) = 1.15°. As a roof pitch it is 0.24/12, about a quarter inch per foot.

Source Common Core State Standards · High School Geometry, solving right triangles (G-SRT.C.8) ↗

How steep is a 5% slope?

A 5% slope rises 5 for every 100 across: 2.86°, or a pitch of 0.6/12. That is well under the 4/12 that OSHA uses as the line between a low-slope and a steep roof.

Source eCFR · 29 CFR 1926.500(b), OSHA definitions of low-slope and steep roofs ↗

Sources

Related calculators